Landscaping, Irrigation, and More - R & R Sprinkler & Lanscape, Inc. of Cape Coral, Florida Blog

Landscaping, Irrigation, and More

R & R Sprinkler & Lanscape, Inc. of Cape Coral, Florida Blog

Parts of a Lawn Irrigation System – Sprinkler Valve

Posted by Landscaping, Irrigation and More On August 22, 2012

If you are like the average homeowner you don’t really know what the specific parts are that make up your irrigation system. You just want it to turn on and water your grass and landscaping. We understand, you might know what the stock market is doing today, you may know the part I need to repair my air conditioner or you may know how to teach my daughter math (all things I may struggle with myself) but you don’t know what an irrigation valve is. That’s OK. We all have gifts and talents. Servicing and educating customers about their irrigation system is ours.

Today we’re going to tell you about irrigation valves. A sprinkler system is made up of many parts. It’s not about just throwing pipes in the ground and your grass is watered. There are rotor heads, spray heads, timers, rain sensors, fittings, pipe and valves. A valve is the part of the sprinkler that determines a sprinkler “zone”. It’s the brain for a specific part (zone) of the entire sprinkler system. The valves talk to the timer so the timer can tell the valves when to open and close to let water flow into the pipes and out of the sprinkler heads and for how long.

Each valve is wired to the sprinkler timer. If valves are not operating there is either not power running from the timer to the valve or one of the electrical wires has been somehow damaged. If valves get stuck open there may be debris stuck in the valve. A common result of this would be a flooded yard. If valves are weeping you may need to replace the seal around the valve. The most important thing you can do is to know where your valves are located for your sprinkler system.

One of the most time consuming tasks we perform during an irrigation repair to locating valves. If you can keep your valves located and clear from your yard growing over top of them you will save a lot of labor for your next sprinkler repair.

R & R Sprinkler and Landscape have expert technicians ready to locate and repair the valves to your sprinkler system today.

Rotor Heads are Sprinkler Heads

Posted by Landscaping, Irrigation and More On August 9, 2012

PGP-ADJ Hunter Industries

A rotor head is a component of a sprinkler system that delivers water to your lawn. It’s typically referred to as a sprinkler head. The purpose of the rotor head is to deliver water to your grass in a slow even application. At R & R Sprinkler and Landscape we install rotor heads that will spray water in a steady stream of up to 50′. We want to give you the maximum amount of coverage delivered using the smallest amount of water by proper installment and adjustment of your sprinkler head.

Our sprinklers are installed and repaired with the end result of water conservation in mind. This is better for the environment and will result in a lower water bill for the end user.

A typical sprinkler head is attached to underground pipe with fittings. It will rise @ 4″ above ground level when it pops up to water the lawn and will fully retract into the ground when not in use. Make sure you keep the area around the rotor head cleaned out from the growth of grass and your lawn mowed at a proper height to avoid interference of watering.

Whether you need a new sprinkler system or repair to your existing irrigation system R & R Sprinkler is your first and best choice.

Contact us to evaluate your system and make changes that will help with water conservation and a lower utility bill for you. We have one of the best service departments for sprinkler repair in Southwest Florida. We call evaluate whether you need a simple sprinkler repair, whether you need a irrigation system renovation, or if you need to start over with a new sprinkler system installation.

Get a quote to install a new irrigation system. We will design a sprinkler for full coverage of your property. It’s a great investment to your property.

Lee County Florida Licensing Requirements for Irrigation Contractors

Posted by Landscaping, Irrigation and More On August 1, 2012

Lee County Licensing Requirements for Irrigation Contractors

Most folks think that obtaining an occupational license gives them permission to perform any type of work. This is a false mis-conception. You are paying a business tax that allows you to be in business but does not allow you to perform just any kind of trade activity. You must be State Certified OR receive a Certificate of Competency for Lee County. In addition, you must apply for a State or Specialty Trade Contractor’s License for each city municipality you are going to perform work in.

To install or repair an irrigation system in Lee County we must obtain not only an occupational license but also a license as a specialty trade contractor as per Lee County Ordinance No: 00-26.

As a contractor that will perform installation with and for a water source the Board of County Commissioners recognizes that the work an irrigation contractor performs for and on sprinkler systems could be harmful or could pose a danger if not performed by a competent, honest, educated contractor.

Furthermore, we’d be required to be State Certified if we were performing any type of installation or hook up to a potable water source that did not have a backflow prevetor in place. Currently we connect our new irrigation sprinkler systems to the following:

1. A potable water source that has a backflow preventor in place
2. A well
3. A reclaimed water system
4. Other water sources that draw water from canals and retention areas by permit

We are not only required to be licensed as a specialty trade contractor in Lee County, but also in all cities and municipalities we install or repair irrigation systems. This includes but is not limited to The City of Fort Myers, The City of Cape Coral, The City of Bonita Springs, The City of Fort Myers Beach, etc.

The same rules and reguations apply in Charlotte County Florida and Collier County Florida.

In summary, make sure that anyone that installs a new sprinkler system or perform repairs to your existing irrigation system has a Specialty Trade Contractor’s License.

If you’d like a list of current Counties and Cities that R & R Sprinkler and Landscape are permitted to provide new irrigation system installation or repair to existing sprinkler system please contact us. If any company is reluctant to provide this information to you perhaps you should reconsider doing business with them.

Delivering Water To Your Plants With Drip Irrigation Emitters

Posted by Landscaping, Irrigation and More On July 17, 2012

An emitter is an element of a drip irrigation system that transfers water from the water source to the plant, tree or shrub it is intended to water. Emitters have also been referred to as drippers since they apply water to the landscaping through a slow steady drip to the landscape roots.

There are three types of emitters:
1. High Flow Emitters – intended to water larger trees and shrubs. They yield an average output of 5 gallons per hour.
2. Medium Flow Emitters – intended for plants and shrubs @ 24″ wide. They yield an average output of 2 gallons per hour.
3. Low Flow Emitters – intended for small starter plants, shrubs and flowers. They yield an average output of 1 gallon per hour.

Emitters are installed into 1/4″ – 1/2″ tubing called drip line. The tubing is punctured and the emitter is installed into the tubing with an insertion tool. Emitters come as open flow emitters, fixed flow emitters or variable flow emitters. Having emitters that regulate the volume of water applied as well as the type of water flow will help you water your roses differently then your Queen Palm.

We would be happy to help you design and install a drip irrigation system using flow emitters for you.

The History of Drip Irrigation

Posted by Landscaping, Irrigation and More On July 5, 2012

Drip irrigation dates back to the 1800’s in Afganistan where the farmers used it to water their clay pots. Germany, Australia and Israel made more contributions to the evolution of the drip irrigation systems.

Drip irrigation is an alternative to traditional surface irrigation. It’s popular because it conserves water, reduces evaporation and water drainage and provides precise water application through emitters, bubblers and tubing that drip slowly to plant roots. Traditional irrigation system use sprinkler heads that mist and spray water. Drip Irrigation is also known as trickle irrigation, micro irrigation, localized irrigation and spot watering.

The ideal scenarios to use drip irrigation are localized ground cover, landscape beds, vegetable gardens, rose gardens, container watering and flower boxes.

R & R Sprinkler specializes in the installation of drip irrigation systems. Let us give you a quote today.